Vintage, yesteryear and retro biking
20 posts • Page 1 of 1
Having had success with my question about polished aluminium I will ventre into my next problem with restoration of my Chesini X-Uno. I was fortunate to get a NOS C-Delta brake engraved with Chesini. Unfortunately there was only one. I have bought another standard C-Delta and would like to engrave the Chesini name and logo onto the aluminium cover plate. I have tried a number of engravers and they all say no, so now I am chasing a CNC engraver. Has anyone used successfully a CNC engraver in the Brisbane Gold Coast area. If I am not successful I have even thought about doing it myself. I have a small engraver so will try on scrap first. The original which has obviously been routed is a little rough. Alternatively someone may have a Chesini C-Delta brake cover collecting dust and would like to see it on a finished bike.
you could think about this company (in USA). It was my Plan B when I was getting the engraving done on the Shockstop master.
The replies were prompt and the pricing was sensible, and they seem to know their way around bike parts.
Last edited by Clydesdale Scot on Wed Feb 06, 2013 2:38 pm, edited 1 time in total.
ˈfiləp/ a movement made by bending the last joint of a finger against the thumb and suddenly releasing it
I'am a retired hand engraver, I would not touch aluminium with my experience. As far as an engraving metal (by hand) it is CRAP & should only be attempted by a revolving cutter in a mechanical engraver, eg pantograph machine.
We used to cut logos , like a Rotary wheel which was quite complicated, but you started large, tracing a paper logo by hand & kept reducing untill the pattern had straight lines, once you had the plastic pattern it could be reproduced over & over.
( I should start up again??)
I'm a machinist and I do CNC engraving. But a one off job on a 3D curved surface would involve laser scanning the surface then generating toolpaths in CAM. Then you would have to jig the part in the correct orientation. If you could find someone capable and interested it would likely be in the range of $300-500.
Thanks again guys for your comments and help. I was only joking when I said I'll engrave myself. It has been hard enough painting the bike frame myself with all the fancy line shadowing so I don't want to start a new skill. Warren's friend George Hamilton says he can do it on his panograph so I have sent them to him. I did get a reply from Perfect Perforations in the States and they can do it as well if I supply a tiff file which I can do. Anyway I will see how I go with George. He has old bikes himself so is a sympathetic machinist.
Keep us in the loop
I sent the two plates to George and spoke to him yesterday. He has no problems in copying the logo and Chesini to the blank plate on the left. He did say that the paintwork in the logo and letters may get scratched. This is not a problem for me as I will repaint them. He thought the original Chesini plate was beautiful so I hope I can reproduce the paint detail on the blank plate. Will let you know when I receive them.
Stage 2 completed by George Hamilton in Melbourne. Thanks again to Warren Meade for introducing George to me.
Now to replicate the paint job. Base coat, masking, shadow top coat, remove masking, dusting top coat, three clear coats and then painting the lettering by hand. Hope to have it ready for the Gold Coast Retro Ride on the 13th April if the bl....y rain stops by then.
This is so awesome.
I think the most difficult part will be keeping the coats so light that the Campy logo still cuts through.
Well I have finished it for the first time. Found that dusting coats are very difficult but because it took so long and I wanted to ride the bike so I accepted what I had done and will redo when I have found some more patience. Have a look at the "Shows us what you got" post for all photos.
20 posts • Page 1 of 1
Who is online
Users browsing this forum: No registered users