fork trouble
-
- Posts: 13
- Joined: Mon Oct 21, 2013 9:16 pm
fork trouble
Postby brutusobrien84 » Mon Oct 21, 2013 9:32 pm
hi everyone. iv noticed a bit of a problem with my front fork. its a rock shox recon and its about 18 months old. its been used quite regularly 2to4 times a week. i really look after the bike, clean it after every ride and always clean and lube the stanchions. but lately iv noticed that when i apply pressure first the fork sticks, i have to give it a good bounce before it works, then it works fine until its been idle for a little bit.
so im wondering has anyone else had this problem? or is it something that i shouldnt be that worried about. thanks !
so im wondering has anyone else had this problem? or is it something that i shouldnt be that worried about. thanks !
- Duck!
- Expert
- Posts: 9858
- Joined: Tue May 21, 2013 8:21 pm
- Location: On The Tools
Re: fork trouble
Postby Duck! » Mon Oct 21, 2013 9:58 pm
Air or coil spring?
I had a thought, but it got run over as it crossed my mind.
-
- Posts: 13
- Joined: Mon Oct 21, 2013 9:16 pm
- FuzzyDropbear
- Posts: 330
- Joined: Wed Aug 15, 2012 7:55 pm
- Location: Ballarat, VIC
Re: fork trouble
Postby FuzzyDropbear » Tue Oct 22, 2013 11:25 am
How long since the bottoms have been serviced?
Sounds to me like there's no, or little grease in the bottoms, causing the seal to stick a bit. That's what happens to my coil forks after a while anyway. The grease is gradually used up as the forks are compressed and rebound again (think the lube you wipe off the stanchions), so it needs a top up every so many hours (the service manual for your forks should give you this info).
Not a huge job as long as you have a few basic tools and some grease.
Sounds to me like there's no, or little grease in the bottoms, causing the seal to stick a bit. That's what happens to my coil forks after a while anyway. The grease is gradually used up as the forks are compressed and rebound again (think the lube you wipe off the stanchions), so it needs a top up every so many hours (the service manual for your forks should give you this info).
Not a huge job as long as you have a few basic tools and some grease.
- Duck!
- Expert
- Posts: 9858
- Joined: Tue May 21, 2013 8:21 pm
- Location: On The Tools
Re: fork trouble
Postby Duck! » Tue Oct 22, 2013 1:47 pm
Ensure you use a non-lithium-based grease, otherwise you run the risk of an electrolytic reaction with the magnesium lower casting.
While you're pulling it all apart it's worth giving the rebound/lockout side a service too, replacing the internal seals & oil.
While you're pulling it all apart it's worth giving the rebound/lockout side a service too, replacing the internal seals & oil.
I had a thought, but it got run over as it crossed my mind.
-
- Posts: 13
- Joined: Mon Oct 21, 2013 9:16 pm
Re: fork trouble
Postby brutusobrien84 » Tue Oct 22, 2013 2:19 pm
It had a full service last Xmas. So if that is grease is the problem it's well dry. Ok sounds good. Thanks for your replies!!
-
- Posts: 13
- Joined: Mon Oct 21, 2013 9:16 pm
Re: fork trouble
Postby brutusobrien84 » Tue Oct 22, 2013 9:24 pm
by the way. is there a particular brand of non lithium grease? is it something i can get in my lbs? also will i need oil for the forks? i gave it quick google and a look on srams fork guide and it seems i need oil for the bottoms.
- Mulger bill
- Super Mod
- Posts: 29060
- Joined: Sun Sep 24, 2006 2:41 pm
- Location: Sunbury Vic
Re: fork trouble
Postby Mulger bill » Tue Oct 22, 2013 9:50 pm
I've always been happy with Slick Honey so haven't researched alternatives, I'm sure there's some out there.
...whatever the road rules, self-preservation is the absolute priority for a cyclist when mixing it with motorised traffic.
London Boy 29/12/2011
London Boy 29/12/2011
- Duck!
- Expert
- Posts: 9858
- Joined: Tue May 21, 2013 8:21 pm
- Location: On The Tools
Re: fork trouble
Postby Duck! » Tue Oct 22, 2013 10:14 pm
Any automotive shop should have a non-lithium grease in the range somewhere. You'll also be able to find fork oil there too.
If you're only servicing the spring side you won't need oil, but you definitely will if you dig into the rebound/lockout side. You'll need two "weights" (densities) of oil, 15wt (heavier & stickier) for lubricating the o-rings, and 5wt (lighter & better-flowing) for the oil bath that does the rebound damping & compression locking.
If you're only servicing the spring side you won't need oil, but you definitely will if you dig into the rebound/lockout side. You'll need two "weights" (densities) of oil, 15wt (heavier & stickier) for lubricating the o-rings, and 5wt (lighter & better-flowing) for the oil bath that does the rebound damping & compression locking.
I had a thought, but it got run over as it crossed my mind.
-
- Posts: 13
- Joined: Mon Oct 21, 2013 9:16 pm
Re: fork trouble
Postby brutusobrien84 » Tue Nov 05, 2013 8:52 pm
hi again. i finally got the time time to service the forks. there was barely any oil left in them. i followed srams instructions to a tee and all went well. until i was refilling it with oil and the tip of the syringe broke. it was still ok to measure oil, but harder to get the oil in the fork.i probably did spill a bit but i didn't think it was much. the thing is when i put the forks back together, they still stick. if anything even worse than they did before hand… would this be because of that little bit oil that was spilled??
- Duck!
- Expert
- Posts: 9858
- Joined: Tue May 21, 2013 8:21 pm
- Location: On The Tools
Re: fork trouble
Postby Duck! » Tue Nov 05, 2013 9:04 pm
Here's a thought.... Is your lockout functioning correctly? I came across a Recon a few years ago where the lockout wasn't working, but the fork wasn't compressing freely either. What had happened was there was breakage in the damper cartridge, resulting in limited oil flow. The compression damper/lockout cartridge has a rod down the guts of it to connect the dial (or remote atachment if applicable) at the top to a "tap" at the base, which shuts off oil flow when in the locked position. On top of the tap is a vane which fits into a slot in the end of the twist rod; this had broken on the fork I encountered, so the tap was stuck in a partially-open position. The restricted oil flow slowed the compression rate of the fork, but would not allow it to fully lock either.
Could be worth a look.
Could be worth a look.
I had a thought, but it got run over as it crossed my mind.
-
- Posts: 668
- Joined: Thu Mar 26, 2009 5:33 pm
Re: fork trouble
Postby DarrylH » Wed Nov 06, 2013 8:03 pm
I've also had problems with the lockout not functioning correctly but it was because the lockout mechanism had partly unscrewed from the cap. If I remember correctly, the cap screws into the fork clockwise but the lockout screws anticlockwise into the cap. As the lockout was fairly tight in the fork, as I screwed the cap in, it was unscrewing the lockout.
Jump to
- General Australian Cycling Topics
- Info / announcements
- Buying a bike / parts
- General Cycling Discussion
- The Bike Shed
- Cycling Health
- Cycling Safety and Advocacy
- Women's Cycling
- Bike & Gear Reviews
- Cycling Trade
- Stolen Bikes
- Bicycle FAQs
- The Market Place
- Member to Member Bike and Gear Sales
- Want to Buy, Group Buy, Swap
- My Bikes or Gear Elsewhere
- Serious Biking
- Audax / Randonneuring
- Retro biking
- Commuting
- MTB
- Recumbents
- Fixed Gear/ Single Speed
- Track
- Electric Bicycles
- Cyclocross and Gravel Grinding
- Dragsters / Lowriders / Cruisers
- Children's Bikes
- Cargo Bikes and Utility Cycling
- Road Racing
- Road Biking
- Training
- Time Trial
- Triathlon
- International and National Tours and Events
- Cycle Touring
- Touring Australia
- Touring Overseas
- Touring Bikes and Equipment
- Australia
- Western Australia
- New South Wales
- Queensland
- South Australia
- Victoria
- ACT
- Tasmania
- Northern Territory
- Country & Regional
Who is online
Users browsing this forum: No registered users
- All times are UTC+11:00
- Top
- Delete cookies
About the Australian Cycling Forums
The Australian Cycling Forums is a welcoming community where you can ask questions and talk about the type of bikes and cycling topics you like.
Bicycles Network Australia
Forum Information
Connect with BNA
Brought to you by Bicycles Network Australia | © 1999 - 2024 | Powered by phpBB ®
This website uses affiliate links to retail platforms including ebay, amazon, proviz and ribble.
This website uses affiliate links to retail platforms including ebay, amazon, proviz and ribble.