Questions about purchasing bicycles and parts
14 posts • Page 1 of 1
I want to attach a second drink holder to my wife's Trek MTB and the problem is that there is only 1 set of threads for 1 drink holder.
So, I have worked out where the new one will go, used cable ties for the past 2 months to make sure she is happy with it, but now I have to go to the next step and attach it securely.
So what are my options? I could use stainless stelf self tappers, but from my days of owning a boat, I know stainless & aluminium don't like each other too much. I could use alloy rivets, but I think with constantly pulling a water botle in and out would eventually loosen them and create a problem for myself.
What does everybody think? Any other suggestions?
Becareful. Bike tubing are typically very thin, they won't be able to hold a thread without some weld-on reinforcement inside or outside.
I'd say you'll be better off to use one of those tie-on solutions. Or there are bottle holders you can attach to seatpost or handlebar.
Bianchi, Ridley, Montague, GT, Garmin and All things Apple
I wouldn't go drilling holes in the frame at all. Rivets might work but I share your concerns. There isn't enough metal to tap the holes out nor to give a secure hold with a self tapping screw, that's without the issue of non-like metals.
Your best bet is to use clamps. You used to be able to buy drink bottle holders that clamped on, maybe you still can. Failing that, just search for a suitable clamping system. Hose clamps will do the job but are a tad unsightly, I would however, use them until something more suitable turned up - for instance, some plastic light clamps would do the job (many wouldn't). It's just a matter of keeping your eyes open.
A brutal job could be done with duct tape too - just tape the thing in place. It'd be effective but the aesthetics would be an issue.
A bit of tape under the clamp will stop it sliding around without excessive clamping pressure (something to think about on an ally frame).
Just been down to the lbs to buy some bar tape (the other stuff didn't handle being scraped down the road at 30km/hr very well). I asked about bottle holders with clamps - 'no, they don't make them. There are too many different sized downtubes to make it worth it'. Yeah, right. The bicycle industry at its best - you buy what we want to fuss with and to hell with you
Anyways, you might find some old stock somewhere. Apparently there are some that use velcro but I wouldn't bother.
Well - I don't know, but I saw some in an LBS here in Perth just last weekend when I was looking for a new bottle cage. Plastic, with a clamp that bolted together at the back.
That's what really annoys me about the industry. You know stuff is available but if they don't have it on the floor, it doesn't exist. Sheesh, and they complain about loyalty and the internet.
For those in Adelaide, Super Elliots in Rundle Street do a single bottle plastic holder with a metal clamp that would work on a seat post or handle bar for the princely sum of $11.95 ea.
Profile make a 2 bottle Triathlon style holder that goes on the seat post for $54 that I have seen in a couple of shops (higher end though).
However, drilling holes in a frame would be equivalent to removing a few wheel nuts to save weight - quick road to absolute disaster
What you should use are Rivnuts. These are a threaded insert that gets installed like a rivet. A special tool is required. here's a link to what they look like. http://www.aircraftspruce.com/catalog/hapages/rivnuts.php
you might need to do some research as to where to get them in Aus.
I wrap electrical tape around the frame and then use car radiator hose clamps to hold the cage onto the frame. They have to be a particular type of cage that has the lugs for the screw holes at each end. It makes it a lot easier to attach with this type.
I put mine on with hose clips
Burn plenty of Glycogen
Frame Size Calculator.....Park Tools Repair Guides Frame Size Calculator.....Rolling Resistance.....Rolling Performance.....Sheldon Brown's Bicycle Technical Info
training log.....Body-Mass Index, Waist-to-Height Ratio, Basal Metaboic Rate
Bicycle FAQs.....Bicycle Safety.....Cadence in Cycling.....Types of Bicycles
If the R-1 rule is broken, what happens to N+1?
That's a load of bullsh**t they're trying to feed you. I've got a clamp-on one that I had on my last MTB and it worked a treat. It uses the same "over-centre" locking principle as the quick release mechanism on wheels and would fit a variety size of frame tubes. I'll see if I can see a brand name on it tomorrow and let you know who the manufacturer is.
14 posts • Page 1 of 1
Who is online
Users browsing this forum: Bing [Bot]