Hi,
As the title suggests, how do you go about servicing BBB road pedals.
My right pedal has a click, it feels as though if it has cones then they need tightening. Just a small amount of play that, with the amplification effect of the frame, becomes too annoying! They are only about 1000km old and will still be under warranty, I was just a little foolish and chose a LBS that is not very local..... a bit of a pain to take in.
Thanks in advance,
Justin
Servicing BBB road pedals
-
- Posts: 9
- Joined: Sat Feb 21, 2009 11:10 pm
- greyhoundtom
- Posts: 3023
- Joined: Sun May 31, 2009 6:28 am
- Location: Wherever the sun is shining
- Contact:
Re: Servicing BBB road pedals
Postby greyhoundtom » Thu Dec 13, 2012 6:47 am
While I have never had the opportunity to pull one apart, as far as I know you need a special tool to undo the lock ring located just in front of the pedal body.
There are three sealed internal bearings on the pedal shaft, and by the sounds of it at least one of those has given up the ghost.
If one or more bearings need replacing a trip to your LBS might still be your best bet.
There are three sealed internal bearings on the pedal shaft, and by the sounds of it at least one of those has given up the ghost.
If one or more bearings need replacing a trip to your LBS might still be your best bet.
-
- Posts: 9
- Joined: Sat Feb 21, 2009 11:10 pm
Re: Servicing BBB road pedals
Postby jham66 » Fri Dec 14, 2012 6:08 am
Thank you. I was hoping I didn't need specialist tools, couldn't find a way in though.....
-
- Posts: 9
- Joined: Sat Feb 21, 2009 11:10 pm
Re: Servicing BBB road pedals
Postby jham66 » Sun Jan 13, 2013 3:42 pm
Just updating. I had misdiagnosed the problem. I have a Cannondale CAAD10, it has a BB30 bottom bracket. The BB was a bit dry of lube and had some grit in there too, I have been caught in quite a few storms lately and obviously a bit of grime got flicked up with all the water. After removal of the crankset and cleaning out the old grease, applying some quality grease in its place....... the sound is gone! I did not remove the pressed in bearings. There is still a small click in the pedal, but not an issue I will rectify right now.
Jump to
- General Australian Cycling Topics
- Info / announcements
- Buying a bike / parts
- General Cycling Discussion
- The Bike Shed
- Cycling Health
- Cycling Safety and Advocacy
- Women's Cycling
- Bike & Gear Reviews
- Cycling Trade
- Stolen Bikes
- Bicycle FAQs
- The Market Place
- Member to Member Bike and Gear Sales
- Want to Buy, Group Buy, Swap
- My Bikes or Gear Elsewhere
- Serious Biking
- Audax / Randonneuring
- Retro biking
- Commuting
- MTB
- Recumbents
- Fixed Gear/ Single Speed
- Track
- Electric Bicycles
- Cyclocross and Gravel Grinding
- Dragsters / Lowriders / Cruisers
- Children's Bikes
- Cargo Bikes and Utility Cycling
- Road Racing
- Road Biking
- Training
- Time Trial
- Triathlon
- International and National Tours and Events
- Cycle Touring
- Touring Australia
- Touring Overseas
- Touring Bikes and Equipment
- Australia
- Western Australia
- New South Wales
- Queensland
- South Australia
- Victoria
- ACT
- Tasmania
- Northern Territory
- Country & Regional
Who is online
Users browsing this forum: No registered users
- All times are UTC+10:00
- Top
- Delete cookies
About the Australian Cycling Forums
The Australian Cycling Forums is a welcoming community where you can ask questions and talk about the type of bikes and cycling topics you like.
Bicycles Network Australia
Forum Information
Connect with BNA
Brought to you by Bicycles Network Australia | © 1999 - 2024 | Powered by phpBB ®
This website uses affiliate links to retail platforms including ebay, amazon, proviz and ribble.
This website uses affiliate links to retail platforms including ebay, amazon, proviz and ribble.