I'm having trouble removing the cranks from the BB.. not sure why, I'm using the crank removing tool, where after removing the bolts, i screw the first part into the thread, then screw the bit that pushes through the middle to lever the crank arm off the BB.
It's not working though, i tighten it and it just sticks, I can't get the arm to budge at all.
Any advice?
removing cranks, help please.
- janus77
- Posts: 817
- Joined: Mon Aug 27, 2007 3:09 pm
- Mulger bill
- Super Mod
- Posts: 29060
- Joined: Sun Sep 24, 2006 2:41 pm
- Location: Sunbury Vic
Postby Mulger bill » Sat Jun 14, 2008 9:39 pm
At a guess Janus, square taper BB and a fairly late model crankpuller?
If so, the bit on the end of the "pushy" bit that contacts the crank spindle prolly has some sort of oversize adaptor cap on it to fit ISIS and octalink spindles which are a bit fatter. Have a look, see if you can get it off.
Shaun
If so, the bit on the end of the "pushy" bit that contacts the crank spindle prolly has some sort of oversize adaptor cap on it to fit ISIS and octalink spindles which are a bit fatter. Have a look, see if you can get it off.
Shaun
...whatever the road rules, self-preservation is the absolute priority for a cyclist when mixing it with motorised traffic.
London Boy 29/12/2011
London Boy 29/12/2011
- janus77
- Posts: 817
- Joined: Mon Aug 27, 2007 3:09 pm
Postby janus77 » Sun Jun 15, 2008 12:33 pm
Got the BB out, cleaned it up (sealed bearing type, so not much to be done, bit of lube around the bits..), put everything back together.
I stuffed up the chain!! damnit, I removed one of the link pins completely by mistake. Ended up dabbing a bit of grease around the link hole so that the pin would sit in place on it's own while I put it in the chain breaker, anyway, I might have put the outside part of the sleeve in the breaker without slipping the other link in to try to get it connected. Think I've bent that particular chain link, because now that I've got it back together it sticks, the link is all locked up.
What's my best option here? Remove that link and get a replacment link to put in (Great, will have the same probelm getting the link pin back in), or go for a whole new chain? Or finally undo it and try to bend it back out a bit so it moves properly?
Cheers.
I stuffed up the chain!! damnit, I removed one of the link pins completely by mistake. Ended up dabbing a bit of grease around the link hole so that the pin would sit in place on it's own while I put it in the chain breaker, anyway, I might have put the outside part of the sleeve in the breaker without slipping the other link in to try to get it connected. Think I've bent that particular chain link, because now that I've got it back together it sticks, the link is all locked up.
What's my best option here? Remove that link and get a replacment link to put in (Great, will have the same probelm getting the link pin back in), or go for a whole new chain? Or finally undo it and try to bend it back out a bit so it moves properly?
Cheers.
- il padrone
- Posts: 22931
- Joined: Mon Apr 07, 2008 11:57 pm
- Location: Heading for home.
Postby il padrone » Sun Jun 15, 2008 12:55 pm
Is this a Shimano chain?
Because they recommend rejoining the chain with their special link pin (a longer one, with a 'pencil' tip that you push through then snap the end off). If you just push the existing links back in you damage the special edges on them, and eventually they'll come out - broken chain!!
The little pins are ridiculously expensive, something like $2.50 for one. And you need a new one each time you break the chain to clean it. A much better option is to spend a bit more and get a Connex or Sram joining link. They're re-usable and make it much quicker to break your chain for cleaning - no tools needed. Phantom has these listed as MTB parts, but they're 9 spd so should be compatible with road 9 spd too, I believe.
Go ask about these at your LBS. Any decent shop will stock them.
Because they recommend rejoining the chain with their special link pin (a longer one, with a 'pencil' tip that you push through then snap the end off). If you just push the existing links back in you damage the special edges on them, and eventually they'll come out - broken chain!!
The little pins are ridiculously expensive, something like $2.50 for one. And you need a new one each time you break the chain to clean it. A much better option is to spend a bit more and get a Connex or Sram joining link. They're re-usable and make it much quicker to break your chain for cleaning - no tools needed. Phantom has these listed as MTB parts, but they're 9 spd so should be compatible with road 9 spd too, I believe.
Go ask about these at your LBS. Any decent shop will stock them.
Mandatory helmet law?
"An unjustified and unethical imposition on a healthy activity."
"An unjustified and unethical imposition on a healthy activity."
-
- Posts: 1191
- Joined: Sat Jul 21, 2007 12:45 pm
- Location: Canberra ACT
Postby thomas_cho » Sun Jun 15, 2008 1:13 pm
Okay this is not recommended by the manufacturers, but this is what I did to an 8 spd chain. I had to shorten the chain, and while I did not push the whole pin out, I did have the issue about the link getting locked up.janus77 wrote:Got the BB out, cleaned it up (sealed bearing type, so not much to be done, bit of lube around the bits..), put everything back together.
I stuffed up the chain!! damnit, I removed one of the link pins completely by mistake. Ended up dabbing a bit of grease around the link hole so that the pin would sit in place on it's own while I put it in the chain breaker, anyway, I might have put the outside part of the sleeve in the breaker without slipping the other link in to try to get it connected. Think I've bent that particular chain link, because now that I've got it back together it sticks, the link is all locked up.
What's my best option here? Remove that link and get a replacment link to put in (Great, will have the same probelm getting the link pin back in), or go for a whole new chain? Or finally undo it and try to bend it back out a bit so it moves properly?
Cheers.
Firstly visually inspect the pin, and compare it to the neighbouring pin to see if you have pushed it too far, or not enuf. Then flex the chain, ie bend it sideways, to and fro to "loosen" the link. I think this helps the pin to seat properly.
I used the chain in a single speed set up, and on certain ocassions had to stomp hard on the pedals. The chain has held up.
But considering that you did push the pin all the way through, I suggest discarding the join, and using a quick link. Having the chain break on you on a ride is probably not worth saving that $10-20.
Jump to
- General Australian Cycling Topics
- Info / announcements
- Buying a bike / parts
- General Cycling Discussion
- The Bike Shed
- Cycling Health
- Cycling Safety and Advocacy
- Women's Cycling
- Bike & Gear Reviews
- Cycling Trade
- Stolen Bikes
- Bicycle FAQs
- The Market Place
- Member to Member Bike and Gear Sales
- Want to Buy, Group Buy, Swap
- My Bikes or Gear Elsewhere
- Serious Biking
- Audax / Randonneuring
- Retro biking
- Commuting
- MTB
- Recumbents
- Fixed Gear/ Single Speed
- Track
- Electric Bicycles
- Cyclocross and Gravel Grinding
- Dragsters / Lowriders / Cruisers
- Children's Bikes
- Cargo Bikes and Utility Cycling
- Road Racing
- Road Biking
- Training
- Time Trial
- Triathlon
- International and National Tours and Events
- Cycle Touring
- Touring Australia
- Touring Overseas
- Touring Bikes and Equipment
- Australia
- Western Australia
- New South Wales
- Queensland
- South Australia
- Victoria
- ACT
- Tasmania
- Northern Territory
- Country & Regional
Who is online
Users browsing this forum: No registered users
- All times are UTC+10:00
- Top
- Delete cookies
About the Australian Cycling Forums
The Australian Cycling Forums is a welcoming community where you can ask questions and talk about the type of bikes and cycling topics you like.
Bicycles Network Australia
Forum Information
Connect with BNA
Brought to you by Bicycles Network Australia | © 1999 - 2024 | Powered by phpBB ®
This website uses affiliate links to retail platforms including ebay, amazon, proviz and ribble.
This website uses affiliate links to retail platforms including ebay, amazon, proviz and ribble.