Looking for shop that does DI2 software upgrade

auswi2
Posts: 166
Joined: Mon Oct 17, 2011 2:14 pm

Looking for shop that does DI2 software upgrade

Postby auswi2 » Sun Feb 10, 2013 2:19 pm

Hello,

I live in Brisbane and would like to find a shop that does Ultegra DI2 software upgrades as the lbs I brought the bike from does not have the equipment.

I was thinking about the new update that allows the rider to go up and down the rear cassette but holding the shift button.

Thanks

Auswi2

User avatar
Sven Nijs
Posts: 401
Joined: Sat Jan 09, 2010 9:24 am
Location: Sunny Sydney

Re: Looking for shop that does DI2 software upgrade

Postby Sven Nijs » Sun Feb 10, 2013 3:06 pm

Contact:
Shimano Australia
35 Mangrove Lane
Taren Point NSW 2229
1300 731 077.
It's a bit warmer here than Scotland isn't it!

auswi2
Posts: 166
Joined: Mon Oct 17, 2011 2:14 pm

Re: Looking for shop that does DI2 software upgrade

Postby auswi2 » Mon Feb 11, 2013 12:37 pm

Thanks for the info the cost is approx $80.00 for the software upgrade which is really steep

Thanks

auswi2

Crawf
Posts: 1935
Joined: Wed Jan 09, 2008 9:20 pm

Re: Looking for shop that does DI2 software upgrade

Postby Crawf » Mon Feb 11, 2013 2:39 pm

That is damn steep considering it would probably take seconds to do.
I was given a price by a mech in Brisbane of about $40.

User avatar
Sven Nijs
Posts: 401
Joined: Sat Jan 09, 2010 9:24 am
Location: Sunny Sydney

Re: Looking for shop that does DI2 software upgrade

Postby Sven Nijs » Mon Feb 11, 2013 6:54 pm

auswi2 wrote:Thanks for the info the cost is approx $80.00 for the software upgrade which is really steep

Thanks

auswi2

That is steep. You can buy the programmer from the US for $199 (+shipping) and DIY....
It's a bit warmer here than Scotland isn't it!

Dr_Mutley
Posts: 2524
Joined: Fri Jan 11, 2008 2:28 pm
Location: Flagstaff Hill, Adelaide SA 5159
Contact:

Re: Looking for shop that does DI2 software upgrade

Postby Dr_Mutley » Mon Feb 11, 2013 9:54 pm

I think u should name the place charging $80 do all can avoid it...

User avatar
geoffs
Posts: 340
Joined: Wed Feb 21, 2007 10:16 pm
Location: Ashbury

Re: Looking for shop that does DI2 software upgrade

Postby geoffs » Tue Feb 12, 2013 12:54 am

Sven Nijs wrote:
auswi2 wrote:Thanks for the info the cost is approx $80.00 for the software upgrade which is really steep

Thanks

auswi2

That is steep. You can buy the programmer from the US for $199 (+shipping) and DIY....


It costs a bit more than that from the local wholesaler - surprise, surprise. Once you have it though you are unlikely to use it again unless you want to share it with some friends.
The upgrade might take 10 mins all going well, however if one of the bits decides it wants to be difficult about accepting the firmware it may take longer. It took a couple of goes for the battery unit on my bike to work properly.
I reckon $40 is a fair price

petal665
Posts: 1576
Joined: Wed Feb 13, 2008 10:42 am
Location: Red Hill, Brisbane

Re: Looking for shop that does DI2 software upgrade

Postby petal665 » Tue Feb 12, 2013 1:32 pm

How does the Ui2 connect to the PC? I can do 9070 so if it is the same as Ui2 I can do it. The 9070 connects into a port on the junction box, I suspect Ui2 is different.

Crawf
Posts: 1935
Joined: Wed Jan 09, 2008 9:20 pm

Re: Looking for shop that does DI2 software upgrade

Postby Crawf » Tue Feb 12, 2013 3:30 pm

petal665 wrote:How does the Ui2 connect to the PC? I can do 9070 so if it is the same as Ui2 I can do it. The 9070 connects into a port on the junction box, I suspect Ui2 is different.


I think into any spare port whether it be shifters, der' or junction.

http://techdocs.shimano.com/media/techd ... 771121.pdf

petal665
Posts: 1576
Joined: Wed Feb 13, 2008 10:42 am
Location: Red Hill, Brisbane

Re: Looking for shop that does DI2 software upgrade

Postby petal665 » Tue Feb 12, 2013 3:40 pm

Nah. The cable I can get hold of goes from PC into a special port on the front junction box of 9070. It's not the same as Ui2.

User avatar
Sven Nijs
Posts: 401
Joined: Sat Jan 09, 2010 9:24 am
Location: Sunny Sydney

Re: Looking for shop that does DI2 software upgrade

Postby Sven Nijs » Tue Feb 12, 2013 11:35 pm

geoffs wrote:It costs a bit more than that from the local wholesaler - surprise, surprise. Once you have it though you are unlikely to use it again unless you want to share it with some friends.
The upgrade might take 10 mins all going well, however if one of the bits decides it wants to be difficult about accepting the firmware it may take longer. It took a couple of goes for the battery unit on my bike to work properly.I reckon $40 is a fair price

I see your point but that'd be $40 every time you want something changed. So you want full multishift = $40. You ride it a while and decide it's shifting is too slow/fast = $40 more. You change your mind and want only 3 sprocket changes max = another $40. Shimano issue newer firmware = $40 etc etc. Factor in the $80 per visit he was actually quoted....
Sharing with friends is definitely a good idea to recoup the outlay and I know someone who has that intention.

petal665 wrote:Nah. The cable I can get hold of goes from PC into a special port on the front junction box of 9070. It's not the same as Ui2.

but aren't the Etube connectors the same for both 6070 and 9070, therefore you should be able to use the method shown on page 7 (or maybe even 8 ) of the Operating Manual as per Crawf's suggestion? I appreciate that old DA Di2 is entirely different.
It's a bit warmer here than Scotland isn't it!

petal665
Posts: 1576
Joined: Wed Feb 13, 2008 10:42 am
Location: Red Hill, Brisbane

Re: Looking for shop that does DI2 software upgrade

Postby petal665 » Wed Feb 13, 2013 8:38 am

Sven Nijs wrote:
petal665 wrote:Nah. The cable I can get hold of goes from PC into a special port on the front junction box of 9070. It's not the same as Ui2.

but aren't the Etube connectors the same for both 6070 and 9070, therefore you should be able to use the method shown on page 7 (or maybe even 8 ) of the Operating Manual as per Crawf's suggestion? I appreciate that old DA Di2 is entirely different.
The 9070 junction box has a special port for charging and PC connection. It's totally different to the e-tube ports.

See the last picture here

User avatar
pagey
Posts: 184
Joined: Thu Feb 18, 2010 4:09 pm
Location: Rowville Victoria

Re: Looking for shop that does DI2 software upgrade

Postby pagey » Wed Feb 13, 2013 9:12 pm

A good bike shop you have a relationship will do it for free. It takes 5 min
cheers
Pagey


Image

Who is online

Users browsing this forum: OldBloke