Why do better wheel sets work better?
- ohexploitable
- Posts: 235
- Joined: Thu Jun 14, 2012 12:39 am
Re: Why do better wheel sets work better?
Postby ohexploitable » Mon Feb 18, 2013 11:52 pm
what you feel is the money you spent on them
-
- Posts: 727
- Joined: Fri Apr 03, 2009 8:33 pm
Re: Why do better wheel sets work better?
Postby ausrandoman » Tue Feb 19, 2013 5:27 am
ohexploitable wrote:you don't really feel wheels accelerating faster
what you feel is the money you spent on them
- foo on patrol
- Posts: 9056
- Joined: Sat Dec 19, 2009 11:12 am
- Location: Sanstone Point QLD
Re: Why do better wheel sets work better?
Postby foo on patrol » Tue Feb 19, 2013 6:36 am
Foo
Goal 6000km
-
- Posts: 727
- Joined: Fri Apr 03, 2009 8:33 pm
Re: Why do better wheel sets work better?
Postby ausrandoman » Tue Feb 19, 2013 7:02 am
Alpine Classic Extreme. (Note: most of this route is little affected by wind)winstonw wrote: God said heavier aerodynamic wheels are better than lighter aerodynamic wheels, and the more aero the better.
Target time 11 hours. (I have grey hair and bifocals)
1500 gram non-aero wheels or 1900 gram, 80 mm deep section, 20/24 conventional spoke wheels.
Which will be faster? Please show your calculations.
- Marto
- Posts: 1343
- Joined: Wed Feb 16, 2011 2:08 am
- Location: Brisbane
Re: Why do better wheel sets work better?
Postby Marto » Tue Feb 19, 2013 7:29 am
Is that aerodynamic grey hair? (I have neglected hair) What is the cost/benefit of dyeing hair?ausrandoman wrote:Alpine Classic Extreme. (Note: most of this route is little affected by wind)winstonw wrote: God said heavier aerodynamic wheels are better than lighter aerodynamic wheels, and the more aero the better.
Target time 11 hours. (I have grey hair and bifocals)
1500 gram non-aero wheels or 1900 gram, 80 mm deep section, 20/24 conventional spoke wheels.
Which will be faster? Please show your calculations.
-
- Posts: 351
- Joined: Thu Dec 22, 2011 9:44 am
Re: Why do better wheel sets work better?
Postby lump_a_charcoal » Tue Feb 19, 2013 7:37 am
As everybody knows, red goes faster, plus you wouldn't be weighed down by a soul.Marto wrote:Is that aerodynamic grey hair? (I have neglected hair) What is the cost/benefit of dyeing hair?ausrandoman wrote:Alpine Classic Extreme. (Note: most of this route is little affected by wind)winstonw wrote: God said heavier aerodynamic wheels are better than lighter aerodynamic wheels, and the more aero the better.
Target time 11 hours. (I have grey hair and bifocals)
1500 gram non-aero wheels or 1900 gram, 80 mm deep section, 20/24 conventional spoke wheels.
Which will be faster? Please show your calculations.
-
- Posts: 727
- Joined: Fri Apr 03, 2009 8:33 pm
Re: Why do better wheel sets work better?
Postby ausrandoman » Tue Feb 19, 2013 7:50 am
Oh, but I am not weighed down by a soul. I have photographic evidence!lump_a_charcoal wrote:As everybody knows, red goes faster, plus you wouldn't be weighed down by a soul.Marto wrote:Is that aerodynamic grey hair? (I have neglected hair) What is the cost/benefit of dyeing hair?ausrandoman wrote:
Alpine Classic Extreme. (Note: most of this route is little affected by wind)
Target time 11 hours. (I have grey hair and bifocals)
1500 gram non-aero wheels or 1900 gram, 80 mm deep section, 20/24 conventional spoke wheels.
Which will be faster? Please show your calculations.
It's hard to be aerodynamic when it is %#*&^ing cold - except for shoe covers. I shoulda worn shoe covers.
- toolonglegs
- Posts: 15463
- Joined: Fri Jun 29, 2007 7:49 pm
- Location: Somewhere with padded walls and really big hills!
Re: Why do better wheel sets work better?
Postby toolonglegs » Tue Feb 19, 2013 8:07 am
I would have thought nearly half of the distance would be spent at 40 kmph plusausrandoman wrote: (Note: most of this route is little affected by wind)
-
- Posts: 727
- Joined: Fri Apr 03, 2009 8:33 pm
Re: Why do better wheel sets work better?
Postby ausrandoman » Tue Feb 19, 2013 8:18 am
Good point!toolonglegs wrote:I would have thought nearly half of the distance would be spent at 40 kmph plusausrandoman wrote: (Note: most of this route is little affected by wind)
-
- Posts: 727
- Joined: Fri Apr 03, 2009 8:33 pm
Re: Why do better wheel sets work better?
Postby ausrandoman » Tue Feb 19, 2013 8:21 am
Got enough popcorn yet?Mulger bill wrote:My popcorn machine's broken and I can't read about NV wheels without it...ausrandoman wrote:The most important contribution to improved performance is lower aerodynamic drag with reduced weight second.
-
- Posts: 10329
- Joined: Thu Sep 18, 2008 12:10 pm
- Location: Sydney
Re: Why do better wheel sets work better?
Postby Nobody » Tue Feb 19, 2013 8:32 am
I can only assume the "Good regular bicycle" is an upright of some kind, not a drop bar. Also the UCI (I assume TT) bike still seems too good to be true, 137W at 30Km/h?il padrone wrote:Strewth, how does a full tuck with aero bars cost $3000 Nah, nah, forget the wheels and the skinsuit. Get with the real aero plan
Look another data table!!
Looks like it was a hot day.il padrone wrote:Can I ride the neglected bicycle.... please....please....??
Oh !?
- Mulger bill
- Super Mod
- Posts: 29060
- Joined: Sun Sep 24, 2006 2:41 pm
- Location: Sunbury Vic
Re: Why do better wheel sets work better?
Postby Mulger bill » Tue Feb 19, 2013 8:44 am
Found It!ausrandoman wrote:It's hard to be aerodynamic when it is %#*&^ing cold - except for shoe covers. I shoulda worn shoe covers.
It's the mirror that's making it hard for you, you NEED something like this...
Of course the CF version at half the weight and 17 times the price will be better again.
Methinks the "upright" posture caused by the ped you just passed won't be helping either...
Lovin' dat popcorn!
London Boy 29/12/2011
-
- Posts: 727
- Joined: Fri Apr 03, 2009 8:33 pm
Re: Why do better wheel sets work better?
Postby ausrandoman » Tue Feb 19, 2013 9:23 am
Hey, I like the idea of the carbon fibre version! If it's half the weight, I can use two, one on each side of the handlebars, thereby avoiding aerodynamic instability. And the extra expense will make me go even faster!Mulger bill wrote: ... you NEED something like this...
Of course the CF version at half the weight and 17 times the price will be better again.
- Xplora
- Posts: 8272
- Joined: Sat Dec 11, 2010 12:33 am
- Location: TL;DR
Re: Why do better wheel sets work better?
Postby Xplora » Tue Feb 19, 2013 11:46 am
In answer to the OP's question (and this is not based on experience, just collation of data) all the wheelset improvement reviews I've read seem to imply a more positive feeling from the wheels. I'm guessing you probably won't notice it without swapping wheels around. At least they are easy to swap compared to frames
- cyclotaur
- Posts: 1782
- Joined: Wed Jan 26, 2011 1:36 pm
Re: Why do better wheel sets work better?
Postby cyclotaur » Tue Feb 19, 2013 11:58 am
The better wheelsets, designed for speed and handling improvements, are noticeably stiffer and feel more stable and solid especially when cornering. This is an actual physical difference you will definitely notice, especially when swapped onto a bike/wheel package that may have been designed with some comfort in mind.Xplora wrote: In answer to the OP's question (and this is not based on experience, just collation of data) all the wheelset improvement reviews I've read seem to imply a more positive feeling from the wheels. I'm guessing you probably won't notice it without swapping wheels around. At least they are easy to swap compared to frames
As mentioned earlier, when you get a road bike package for, say, up to $1500-2000, you have the basis of an excellent setup. The single biggest improvement would then to be to spend perhaps up to $500 on a lighter, stiffer, slightly aero wheelset for those days you want to ride faster.
That has been my experience.
My old blog - A bit of fun
"Riding, not racing...completing, not competing"
-
- Posts: 351
- Joined: Thu Dec 22, 2011 9:44 am
Re: Why do better wheel sets work better?
Postby lump_a_charcoal » Tue Feb 19, 2013 1:57 pm
-
- Posts: 479
- Joined: Fri Jul 04, 2008 8:33 am
- Location: Maribyrnong,Victoria
Re: Why do better wheel sets work better?
Postby william » Tue Feb 19, 2013 2:13 pm
There are some nice looking wheels and ride like a dog.
I had Mavic Aksium wheels on a nice Bianchi and over 50Kph the bike suddenly felt like I had flatted. Everything looked ok but I reluctantly rode off waiting for something to happen.
Long story short, the design of the wheels was for show, not go and once the wheels got to a certain speed the dynamics of poor design made the wheel twist and squirm under pressure. The spokes were straight pull, crossed twice on the drive and none on the other. The drive side spokes also didn't touch each other which also attributed to poor lateral strength. In short they were good for show and riding around the park.
A tip I got from an ex tour mechanic was to change the pattern so the spokes crossed over each other (touching). Tension to the max and absolute even tension on the drive side and use the non drive to finely true the wheel. All was well after that but I was still cautious. Handling did noticeably improve heaps. Particularly winding descents.
You could say you can make cheap wheels better by knowing a few things like this but a good wheel builder will know it already and may be the person/s to talk to.
- Xplora
- Posts: 8272
- Joined: Sat Dec 11, 2010 12:33 am
- Location: TL;DR
Re: Why do better wheel sets work better?
Postby Xplora » Tue Feb 19, 2013 4:00 pm
-
- Posts: 479
- Joined: Fri Jul 04, 2008 8:33 am
- Location: Maribyrnong,Victoria
Re: Why do better wheel sets work better?
Postby william » Tue Feb 19, 2013 4:48 pm
They are cheap, both cost and quality and I wouldn't go out of my way to buy any. But they can be improved to be a reasonable wheel.
There are other subtle considerations to look at also. Width of spoke flanges. Wider the better. Types of bearings used and if they can be adjusted. A very slight preload is preferred but some mechanics don't know what slight is. You can take the preload away, remove the seals and your wheel will spin forever but... reliability and stability are at risk.
Depth and width of rim, single wall or double, eyelet spoke holes or none. Deeper rim is stronger but harsher and can accommodate less spokes for the same strength.
Aero yes! over 30kph.
What do you need?... What do you want? Silly question really, Want wins nearly every time.
-
- Posts: 10
- Joined: Sun Jun 26, 2011 11:48 pm
Re: Why do better wheel sets work better?
Postby Ginantonicus » Tue Feb 19, 2013 4:57 pm
I'm not sure any of this makes sense to anyone reading it but it makes perfect sense in my head and no I'm not going to do any calculations to prove it (even if I knew how).
- Xplora
- Posts: 8272
- Joined: Sat Dec 11, 2010 12:33 am
- Location: TL;DR
Re: Why do better wheel sets work better?
Postby Xplora » Wed Feb 20, 2013 9:27 am
And if you consider what is happening when you are riding, then the differences between wheels based on his explanation are almost nothing. The rotation of the wheel is virtually the same for any wheel, assuming it is true and stiff. The actual "moment" (the force of momentum? It's been a while) from a 60mm aero rim and a Chinese alloy factory isn't going to be dramatically different because the wheel is round, and weight will be functionally identical the whole way around. A heavy wheel is 1.2kgs, a light one is 600gms. But how much difference in weight at each "point" along the rim? That is his argument.Ginantonicus wrote:I had this conversation with my brother a while ago. Him being the smart arse physics guy that he is said that the part of the bike that dose the most work (eg moves the most) is the wheels. So while the weight difference between wheel sets is small because they are moving so much it creates a larger difference.
I'm not sure any of this makes sense to anyone reading it but it makes perfect sense in my head and no I'm not going to do any calculations to prove it (even if I knew how).
The weight is effectively meaningless from a rotational perspective in relation to acceleration, no more important than the weight of the frame. The wheel isn't doing any "work". Aerodynamics is completely different, but even then, the difference in aero between BSO Chinese wheels and Campy discs is going to be 5-10w maybe. Unimportant for "most riders". Critical for racers. But the coffee shop doesn't need discs.
If the wheels were not attached at a central and UNMOVEABLE point (shudder, imagine that leaving the fork), then the movement might make a difference. MTB wheels may vary for this discussion because there is more motion through the tyre and suspension. But a road bike is naturally opposing weight around the rim, and it starts and stops on a constant axis. The difference to change the speed between a good and bad wheel is negligible, because how much does a couple spokes weigh? I wouldn't want to drag extra spokes along the road for aero reasons, but weight really doesn't make much difference.
If your wheels aren't true, and aren't stiff, then you will get a lot more interference from bumps and moments that aren't acting along the "proper" plane, but you need to be pulling some serious watts for this to make a difference I am guessing. I don't feel any functional difference in the wheels I've had, all low/mid level wheels, and varying weights of tyres and spokes as well.
- clackers
- Posts: 2065
- Joined: Mon May 16, 2011 10:48 am
- Location: Melbourne
Re: Why do better wheel sets work better?
Postby clackers » Wed Feb 20, 2013 9:53 am
Xplora, the difference is bringing the two sets of wheels up to the same speed.Xplora wrote:The rotation of the wheel is virtually the same for any wheel, assuming it is true and stiff. The actual "moment" (the force of momentum? It's been a while) from a 60mm aero rim and a Chinese alloy factory isn't going to be dramatically different because the wheel is round, and weight will be functionally identical the whole way around.
As well as linear momentum, there is angular momentum (think of the identical relationship between force/torque), and more effort is needed to accelerate a heavier wheel.
I've seen a claim that in this respect, saving 250g on wheels is like saving a full kilogram on the frame, although no academic reference was given.
The spokes don't matter so much, it's the rim that is furthest away from the axle.
-
- Posts: 610
- Joined: Tue Jan 20, 2009 9:36 pm
- Location: Adelaide
Re: Why do better wheel sets work better?
Postby gdt » Wed Feb 20, 2013 10:32 am
(CXP33 rims with 32/36 2mm spokes on Ultegra hubs. About $450 for the pair. It does catch crosswinds more than the old wheels, but not enough to be annoying.)
- Xplora
- Posts: 8272
- Joined: Sat Dec 11, 2010 12:33 am
- Location: TL;DR
Re: Why do better wheel sets work better?
Postby Xplora » Wed Feb 20, 2013 1:42 pm
My explanation hopefully focussed on the difference in those two wheels. There is no way you'll get a kilo difference based on angular acceleration, unless your wheels aren't trued or stiff. True and stiff essentially is reducing resistance to that angular acceleration, but we're talking about the difference between the wheels, not the wheels specifically. It's a subjective measurement - Wheel A of a particular stiffness, weight and trueness is of a benefit over Wheel B.clackers wrote:
Xplora, the difference is bringing the two sets of wheels up to the same speed.
As well as linear momentum, there is angular momentum (think of the identical relationship between force/torque), and more effort is needed to accelerate a heavier wheel.
I've seen a claim that in this respect, saving 250g on wheels is like saving a full kilogram on the frame, although no academic reference was given.
The spokes don't matter so much, it's the rim that is furthest away from the axle.
I think about the actual mechanics in motion and if you don't have an absolute dog wheel to start with, the improvements will be marginal. Aero trumps weight for a reason - the forces involved in accelerating the weight are tiny compared to overcoming wind resistance.
- biker jk
- Posts: 7010
- Joined: Tue Nov 17, 2009 6:18 pm
- Location: Sydney
Re: Why do better wheel sets work better?
Postby biker jk » Wed Feb 20, 2013 2:36 pm
http://www.slowtwitch.com/Tech/Why_Whee ... _2106.html
Return to “General Cycling Discussion”
- General Australian Cycling Topics
- Info / announcements
- Buying a bike / parts
- General Cycling Discussion
- The Bike Shed
- Cycling Health
- Cycling Safety and Advocacy
- Women's Cycling
- Bike & Gear Reviews
- Cycling Trade
- Stolen Bikes
- Bicycle FAQs
- The Market Place
- Member to Member Bike and Gear Sales
- Want to Buy, Group Buy, Swap
- My Bikes or Gear Elsewhere
- Serious Biking
- Audax / Randonneuring
- Retro biking
- Commuting
- MTB
- Recumbents
- Fixed Gear/ Single Speed
- Track
- Electric Bicycles
- Cyclocross and Gravel Grinding
- Dragsters / Lowriders / Cruisers
- Children's Bikes
- Cargo Bikes and Utility Cycling
- Road Racing
- Road Biking
- Training
- Time Trial
- Triathlon
- International and National Tours and Events
- Cycle Touring
- Touring Australia
- Touring Overseas
- Touring Bikes and Equipment
- Australia
- Western Australia
- New South Wales
- Queensland
- South Australia
- Victoria
- ACT
- Tasmania
- Northern Territory
- Country & Regional
Who is online
Users browsing this forum: MattyK
- All times are UTC+10:00
- Top
- Delete cookies
About the Australian Cycling Forums
The Australian Cycling Forums is a welcoming community where you can ask questions and talk about the type of bikes and cycling topics you like.
Bicycles Network Australia
Forum Information
Connect with BNA
This website uses affiliate links to retail platforms including ebay, amazon, proviz and ribble.