Questions about purchasing bicycles and parts
I am about to buy some new bottles but have read some reviews that the CamelBak Bottles don't fit some cages. Way to tight etc.
Can anyone recommend a cheap (sub $15 each) cage that fits the Camelbak bottles?
I was thinking maybe the Elite Patao Bottle Cage ( http://www.chainreactioncycles.com/Mode ... delID=5658 )
Or the BBB BBC-31 ( http://www.chainreactioncycles.com/Mode ... elID=78146 )
They fit in the standard plastic Cateye cages on my wife's bike quite OK.
I use mine in a couple of cages like this one they fit fine
Killswitch, I think the answer here seems to be, you've been fed a whole stack of guff by whoever told you the Podiums don't fit. As far as I can tell they are normal sized bottles.
Actually it's not guff. I've a few of the generic cages that many makers use as freebies but in this case they are from Velocity Wheels...and I can provide you every assurance that while the Camelbak Podium bottles fit that cage...they are very tight. So tight that I have actually lost one bottle as a result - I mishandled the pull, dropped the bottle, heard it get crushed by following riders then was told that the backup bus also couldn't avoid it. The solution is a liberal dose of DryGlide or similar.
The Cateye cages (as suggested) are perfect.
Ours is not to reason why...merely to point and giggle
Cateye cages on my son's and my dual suspension mtbs.
They're a bit tight and dirt sticking to the damp bottles results in them getting scratched up, but the clear upside is they *never* rattle out over the rough stuff.
In my experience - no way, not going to happen.
Camelbak's are slightly wider than a normal bottle. They just don't fit all cages.
Just use a standard bottle cage. Preferably something not coloured as the paint scrapes off on your Camelbak over time. I like these http://www.ribblecycles.co.uk/sp/road-track-bike/blackburn-blackburn-bottle-cages-blackburn-chicane-stainless-steel-bottle-cage/blacbotc295000000000
You will be happy with the cages in general, with or without Camelbak bottles. Super lightweight and they look great. Just be careful though - when I first had them on a new bike, I clip-stacked and one of the cages broke as the bike hit the floor. So just be careful not to drop the bike etc as they are just plastic.
Funny thing is, when I bought the cages I bought the Elite Higene bottles which are made for Elite cages and while they fit, they are super super tight and have lots of scratches and scuffs now and have left their paint all over the inside of the cages. The Camelbak on the other hand, fits like a glove. Go figure.
Yep all fitted up now and I can confirm super tight. I push them in just enough to hold them in place. Push too hard and the rubber comes off.
Ill stick with them for a while and see if they loosen up.
Im the same I've got elite custom cages on one bike and find the Big Chill bottles a bit of a tight squeeze, I've never lost one but they aren't a great fit.
I bought 2 of these from Cycling Express http://www.cyclingexpress.com/cycle/cle ... -cage.aspx for next to nothing for my other bike and the fit is much better. The cages are just cheap plastic so I don't how durable they are but no problems so far.
I've got two of these that fit the big chill bottles not being used if anyone wants them. CF from cycling express, didn't match my frame so don't get used
Never underestimate the power of ignorance
Revisiting this - the Camelbak Podiums I got the other day from City Bike Depot in Kent Street fit the Elite Custom Race bidon cages perfectly, yet my other Camelbak Podiums (branded by another LBS) don't fit well at all. Age perhaps...
I find that the Podium fits into the Elite Custom Race cage nicely but the Big Chill version is a little tight.
Hmmmm I am surprised by this... Can someone link me to these "tight" Elite custom race cages?
I've got them and I find them a LOOSE fit with my podium chills. To demonstrate I could wheel my bike along on its back wheel and the cage mounted on the seat post will allow the podium chill to simply slide out!
I've got the black gloss n white cages here and they are loose as!
http://m.torpedo7.com.au/products/EEBTC ... ottle-cage
Maybe there are different manufacturing tolerances with the Elite bottle cages? Thinking it's more the bottle cage than the bottle but could be wrong. I've got probably 20 bottles of various brands at home including the Podium Chill and they all seem to be pretty close in tightness in my Elite cages.
Who is online
Users browsing this forum: JDog